摘要：

Subject to technical changes Copyright ©2011 S:FLEX Inc.Page1of15Assembly InstructionsPitched Roof Application*for framed PV-ModulesNeeded tools and materials►Open Ended Wrenches (10,13)►Metric Allen Wrenches or Driver sizes:M(5,8)►Cordless screwdriver►Approved flashing systemor standoff device for the attachment of the systemon the roof►Stainless steel screws,bolts and hardware shall be used for attaching to S:FLEX rails and materialsto prevent galvanic corrosion.Where different metals are used in combination,insulation shall beused to break all contact between metals.We want to point out that our mounting instructions reflect the state of technology and our experience on how to installour systems on site.Due to the fact that each roof has individual characteristics,we highly recommend commissioning aprofessional assessment before beginning the installation.In particular it is necessary to take into account staticrequirements.During the installation of the system,bear in mind the compliance with the corresponding norms andlegislation referring to the prevention of accidents (see also page 15).Subject to technical changes Copyright ©2011 S:FLEX Inc.Page2of15S:FLEX's pitched roof systems are designed fromthe Angle Bracket up and must be attached to an approvedand properly installed standoff or flashing systemof the installer's choice.Angle Brackets must have hardware installed beforeinstallation can begin.To do this,insert one of the T-Boltsprovided and loosely fasten with a nut and washer.See Figure 1.1Approved flashing or standoff devices are to be properlyinstalled along the desired plane for the installation of themounting rails.The rails that will be mounted on these willserve as the structure to which the solar modules aremounted.Angle brackets can now be fastened to an approved andproperly installed flashing or standoff device such as theQuick Mount PV™version shown here.See Figure 1.3(Torque:Dependent on size of hardware)1.11.2Subject to technical changes Copyright ©2011 S:FLEX Inc.Page3of15Mounting Rail Attachment:Mounting rails can now be attached to the angle brackets.Todo this,simply insert the T-Bolt on the angle bracket into theC-Channel on the side of the mounting rail.Turn the T-Boltclockwise until it stops (approximately ¼ turn).See Figure 2.1(Torque:8 ft.lbs)Note:The serrated edges allow the rail to be adjustedvertically on the angle bracket to desired height.To ensure that T-Bolt is properly aligned make sure that theline on the back of the T-Bolt is perpendicular to the rail and ispointing straight up and down.See Figure 2.2Continue fastening all angle brackets on mounting rails untilthe systemis completely attached to the roof.See next step if a rails need to be joined together.Additional mounting rails can be attached using a splice.Toinstall,simply insert the splice into the end of the rail that willneed to be joined until the rivet on the middle of the splicestops the insertion.Then slide the opposing rail over theexposed end of the splice and push together.Do not attemptto through bolt splice.½" gap or separation between rails isrequired for thermal expansion.See Figure 2.4*Note:There must be attachment points to the roof of any rails that arespliced together.2.12.22.32.4Subject to technical changes Copyright ©2011 S:FLEX Inc.Page4of15Telescope and Anti Slip Hardware Installation (optional):Optional:To best adapt the length of the mounting rails to the moduledimensions,use the pre-assembled telescopic shaft fromS:FLEX.To install,slide the shaft onto the mounting rail andfasten it to the roof hooks.Adjust the length (max.23 inches).See Figure 3.1Now,slide the locking clip onto the mounting rail and tightenthe screw.See Figure 3.2(Torque:8 ft.lbs.)Optional:Before they are mounted,the modules are equipped withanti-slip protection.This is done by attaching ¼ x ¾ in.SS bolts(with the shank downward) with ¼ in.nuts in the lowermounting holes of the module.When mounting large modules(e.g.ASE250),5/16 x ¾ in.SS bolts are used.See Figure 3.3To install the first module,place the anti-slip screw (optional)on

展开